TSB says parts failure responsible for fatal helicopter crash in Fort Good Hope, N.W.T. - Action News
Home WebMail Tuesday, November 26, 2024, 12:00 PM | Calgary | -13.1°C | Regions Advertise Login | Our platform is in maintenance mode. Some URLs may not be available. |
North

TSB says parts failure responsible for fatal helicopter crash in Fort Good Hope, N.W.T.

Jon Lee, the western regional manager of the Transportation Safety Board of Canada, says a tension torsion strap on the helicopter failed, causing it to crash. The TSB is now trying to figure out how and why it failed.

The fatal crash happened 3 years to the day of a similar incident in Alberta

A man sits in a room.
Jon Lee, the western regional manager of the Transportation Safety Board of Canada, said investigators have found the part that led to last week's fatal crash but don't know what caused it to fail. (Luke Carroll/CBC)

The TransportationSafety Board of Canada saysa parts failure is what caused a helicopter crash that killed a wildland firefighter last Fridaynear the Fort Good Hope, N.W.T., airport.

But how and why that part failed is yet to be determined.

The part is a tension torsion strap, a device that holds the majority of the rotor blade onto the main rotor head and is supported by two pins said Jon Lee, the western regional manager of the Transportation Safety Board of Canada (TSB).

"We didn't know how or why it broke, but that was the reason for the blade separating from the rotor head," he said.

Lee said a pilot identified by Great Slave Helicopters on Tuesday as Tom Frith took off at about 1:30 p.m. on June 28 ina Bell 212 to doforest fire suppression work. Shortly after takeoff, said Lee, one of the main rotor blades separated from the rotor head, and then the rotor head itself fell off.

The helicopter then collided with the ground and resulted in a post-impact fire.

Lee said the strap and some other parts havebeen recovered and are at a lab in Ottawa. Adetailed examination is expected totake place next week.

"We'll hopefully get a bit better of an understanding as to the how and the why that strap failed," Lee said.

The manufacturer of the part that broke has been contacted, Lee said,and it is up to individual operators to decide whether to ground their fleets that have that part orto replace them.

Firefighters look at smoke and water falling.
Firefighters respond to a wildfire in Fort Good Hope, N.W.T. On June 28, a pilot flying a helicopter to help with fire suppression died in a crash. (N.W.T. Fire)

Other organizations initially grounded similar helicopters

Afterthe broken strap was recovered, Lee said his organization had learned many operators had voluntarilygrounded various Bellhelicopters out of precaution.

One of those operators wasthe B.C. wildfire service.

"Given the nature of the incident as it was initially reported, there was reasonable cause for caution until more facts were known," wroteJaedon Cooke, a B.C. fire information officer.

A man smiles.
Trevor Mitchell, president and CEO of the Helicopter Association of Canada, credits the Transportation Safety Board of Canada for quickly providing information. (Helicopter Association of Canada)

Lee said the TSBthen communicated that it was the tension torsion strap failurewith various organizations, including Transport Canada and the Helicopter Association of Canada, who could then inform operators.

"These types of helicopters are used for forest fire suppression. And there was a great concern of, you know, those types of activities being curtailed because of the concern about what caused this rotor blade to separate," Leesaid.

Trevor Mitchell, president and CEO of the Helicopter Association of Canada, gave credit to the TSB for providing the information so quickly.

"They were very proactive in getting this information out so that air operators could make very definitive and educated decisions related to their fleet if it were affected," he said.

Exactly 3 years since similar fatal crash

The incident bears some resemblance to another crash that happenedthree years to the day.A Bell 212 helicopter involved in wildfire suppression in Alberta crashed on June 28, 2021, killing the aircraft's pilot.

In that case the issue also involved the tension torsion strap, but it was one of the pins holding it together that failed instead.

A man stares forward.
John Cox, CEO at Safety Operating Systems, says that Bell 212 helicopters are a good machine for fighting wildfires. (Luke Carroll/CBC)

John Cox, an aviation safety consultant and CEO of Safety Operating Systems, said although it's the same type of helicopter that crashed it has likely more to do with what theBell 212s are used for than the helicopters themselves.

"It's utilized in firefighting for example because it can hold quite a lot of water," Cox said.

Cox said firefighting is a challenging environment to fly inwhich is why accidents can happen there, but Bell 212s are proven to be successful in that task.

"You're dealing with a very dynamic environment, subject to a lot of change, both in temperature, wind direction, there are other aircraft in the vicinity," he said.

"But the fact that firefighting crews have been successful with the 212 indicate that this is a good machine for that application."